| Analog Input |
|
| Channels | 4 (simultaneous sampling) |
| ADC Resolution | 24 Bit |
| ADC type | Delta-sigma |
| Sampling rate | 1 kS/s to 128 kS/s |
| Input range | ±10V |
| FIFO buffer size | 2k samples per channel |
| Input Configuration | Differential or pseudo-differential |
| Input impedance | 200 kΩ (between positive input and
negative input) 16.93 kΩ (Between
negative input and chassis ground) |
| Input coupling | AC or DC, software selectable |
Integrated Electronic
Piezoelectric (IEPE) | Current: 2 mA or 0 mA, software
selectable IEPE compliance: 24V |
| Over-voltage protection | ±60V |
| Input common mode range | ±10V |
| Trigger source | Analog or digital, software selectable |
| Trigger mode | Post trigger, delay trigger, middle
trigger, gated trigger, pre-trigger,
post or delay trigger with re-triggering |
| Data Transfer | Programmed I/O, continuous (bulk
transfer mode) |
● DC accuracy (25°C)
| Offset Error (mV) | Gain Error (%) |
| Typical: ±0.15mV | Typical: ±0.15% |
| Max. ±0.3mV | Max. ±0.3% |
● AC Dynamic Performance (typical, 25°C)
? THD, THD+N (Vin = 8.9 Vpk)
| Input configuration | Input Signal
Frequency (fin) | THD | THD+N |
| Differential | 20 Hz to 20 kHz | -94 dB | -91 dB |
| 20 Hz to 46.4 kHz | -89 dB | -88 dB |
| Pseudodifferential | 20 Hz to 20 kHz | -92 dB | -88 dB |
| 20 Hz to 46.4 kHz | -85 dB | -85 dB |
? CMRR
? Bandwidth
| -3dB bandwidth | 0.49 * sampling rate |
| AC cut-off frequency (-3dB) | 0.4 Hz |
| AC cut-off frequency (-0.1dB) | 2.4 Hz |
? Flatness
| Input Signal Frequency (fin) | Flatness |
| 20 Hz to 20 kHz | ±0.01 dB |
| 20 Hz to 46.4 kHz | ±0.15 dB |
? Crosstalk
| Input Signal Frequency (fin) | Crosstalk |
| 1 kHz | -102 dB |
| 46.4 kHz | -95 dB |
? System noise
| Mode | AI Noise |
| High-Resolution (< 52.734 kHz) | 50μVrms |
High-Speed Mode
(52.734 kHz to 128 kHz) | 65μVrms |
? SFDR (Vin = -1 dBFS)
| Input Signal Frequency (fin) | SFDR |
| 1 kHz | 104 dB |
? Dynamic Range (Vin = -60 dBFS, fs=102.4kS/s)
| Input Signal Frequency (fin) | Dynamic range |
| 1 kHz | 100 dB |
| Digital Input / Output |
| Channels | 2 programmable function I/O |
| Compatibility | 3.3V / TTL (single-ended) |
| Compatibility | Input (pull low) |
| Input voltage | Logic low: VIL = 0.8 V max; IIL = 0.2 mA max.
Logic high: VIH = 2.0 V min.; IIH = 0.2 mA max. |
| Output voltage | Logic low: VOL = 0.8 V max; IIL = 0.2 mA max.
Logic high: VOH = 2.0 V min.; IIH = 24 mA max. |
| Over-voltage rotection | -2V ~ +7V |
| Supporting modes | ? Static digital input/output
? Pulse output, max. frequency:4 MHz
? Frequency/Event counter, max.
frequency: 4MHz
? Digital trigger IN
? Synchronization sample clock IN |
| Data Transfer | Programmed I/O |
Note: Function I/O shares the same I/O pins, such that only one of these modes can
be selected at a time.
General Specifications
● I/O connector: Four BNC connectors and 4-pin removable
spring terminals
● Operating temperature: 0 to 55°C (32 to 131?F)
● Storage temperature:-20 to 70°C (-4 to 158?F)
● Power requirements: 5V @ 400mA (USB bus powered)
● Dimensions (not including connectors and stand):
115mm (W) x 150 mm (D) x 40 mm (H) (4.5” x 5.91” x 1.57”)
● Relative humidity: 5% to 95%, non-condensing
GtestWorks自動化測試平臺
GNSSWorks車載衛星定位系統自動化測試系統
ShieldingWorks屏蔽效能測試系統
Vectworks汽車電子部件測試系統
VNAWorks無源器件測試系統
WirelessWorks無線通信測試系統
COMWorks串行總線測試系統
DAQWorks高速數據采集系統
FCTWorks電路板性能測試系統
新能源與電動汽車
電磁兼容性EMC
半導體與器件
中試平臺建設方案
新一代信息技術與智能網聯
高端醫療裝備
自動化測試
高速串行接口測試
低空經濟
